• 首页
  • 期刊简介
  • 编委会
  • 投稿指南
  • 收录情况
  • 杂志订阅
  • 联系我们
引用本文:王 佳,胡旭晓,吴跃成.基于UR5机械臂的轨迹跟踪控制算法研究[J].软件工程,2022,25(6):45-48.【点击复制】
【打印本页】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  
←前一篇|后一篇→ 过刊浏览
分享到: 微信 更多
基于UR5机械臂的轨迹跟踪控制算法研究
王 佳, 胡旭晓, 吴跃成
(浙江理工大学机械与自动控制学院,浙江 杭州 310018)
wangjiajia1118@163.com; huxuxiao@zju.edu.cn; wuyuecheng@126.com
摘 要: 为了在现有基础上提高机械臂轨迹跟踪控制的精度,采用自适应模糊反演控制算法对六自由度机械臂UR5进行轨迹跟踪控制算法研究。用拉格朗日法对UR5机械臂进行动力学建模以避免系统的不确定因素影响。由于UR5机械臂满足Pieper准则,故对其进行模型简化,减少运算量,并用拉格朗日法对前两个自由度进行动力学方程推导,该算法在角位移和角速度跟踪方面都表现出了很好的性能。
关键词: UR5;模型简化;拉格朗日法;轨迹跟踪;自适应模糊反演控制
中图分类号: TP241.2    文献标识码: A
基金项目: 浙江省基础公益研究计划(LGF19E050005).
Research on Trajectory Tracking Control Algorithm based on UR5 Manipulator
WANG Jia, HU Xuxiao, WU Yuecheng
(Faculty of Mechanical Engineering & Automation, Zhejiang Sci-Tech University, Hangzhou 310018, China)
wangjiajia1118@163.com; huxuxiao@zju.edu.cn; wuyuecheng@126.com
Abstract: In order to improve the accuracy of manipulator trajectory tracking control on the existing basis, this paper proposes to study the trajectory tracking control algorithm of 6-DOF (degree of freedom) manipulator UR5 by using the adaptive fuzzy inversion control algorithm. The dynamic modeling of UR5 manipulator is established by Lagrange method to avoid the influence of uncertain factors of the system. Since the UR5 manipulator meets the Pieper criterion, its model is simplified to reduce the amount of computation, and the dynamic equations of the first two degrees of freedom are deduced by Lagrange method. The algorithm shows good performance in angular displacement and angular velocity tracking.
Keywords: UR5; model simplification; Lagrange method; tracking; adaptive fuzzy inversion control


版权所有:软件工程杂志社
地址:辽宁省沈阳市浑南区新秀街2号 邮政编码:110179
电话:0411-84767887 传真:0411-84835089 Email:semagazine@neusoft.edu.cn
备案号:辽ICP备17007376号-1
技术支持:北京勤云科技发展有限公司

用微信扫一扫

用微信扫一扫